Car hoist installation

Installing a car lift can be a very time-consuming ordeal. From ordering the equipment to coordinating its arrival, and eventually putting the equipment together. If you're looking for a trained professional to install a car lift in your area, look no further than JMC Automotive Equipment.

Here at JMC, we have everything you need not only at the best prices but with the right crew of installers. Are you looking for a car lift installer in your area? We will negotiate pricing, arrange delivery and even schedule the installation date. When you have secured the power side column, start working on the offside column, this will be easier and more efficient.

Follow the steps again to install the second column. Once you have both columns secured, you can then move to install the Top Trough Assembly. This is a simple procedure and most of the time you will either need a forklift to raise the bar or you can also raise it with two ladders and two men on each side.

Once placed on top make sure you tighten the bolts. Then you will have the structure and hardest part of the lift already set up. Make sure that if the anchor bolts have become loose while you were tightening the top bar, tighten them again.

Next, we have to install the hydraulic power unit itself. Even though the hydraulic unit is a little heavy, you can install it with the help of someone else. Usually, the unit will come with a Vibration dampener and this must be placed between the Hydraulic unit and the column.

Once you have installed the hydraulic unit, you can fill the unit with hydraulic oil, you will need approximately four gallons. The next thing that you have to do is install the safeties, safety cables, hydraulic lines, power unit hoses, and routing the equalizer cables. Depending on what kind of lift you bought, the installations for these items are always going to be different. However, for most lifts, you always have to install the safety cables through the cylinders in the columns and through the top bar of the lift.

And the same thing goes for the hydraulics lines and power unit hoses. So please read the installation manual and follow the advice step by step. They will direct you exactly on how to install each cable and where it needs to go. One mistake and you might have to redo all your work again. Last but not least, you have the lift arms. This is usually a very simple procedure.

All you have to do is place the lift arms in the correct position and slide the headpins in. Once they are inside and through the holes in the Arm Assembly. Install the Snap Ring into the groove in the lift the headpin on the underside of the lift head. Make sure that the Arm Restraint Gears are properly positioned and adjusted and that each lift arm is positioned in its left and right configuration.

Make sure that the gears are working well before operating the lift. Always remember that you must inspect the gears from time to time to make sure that they are in the correct place. Remember, this is the part of the lift that picks up the cars and holds them for several hours at a time.

If not installed properly you can have a real safety hazard in your repair shop. Make sure that the teeth on the gear ring mesh with the teeth on the gears of the arm restraint. You must also tighten the gear ring bolts.

Always test the lift arm by moving it from left to right and make sure that it can hold up your weight before placing any cars on top of it. Adjust the gear ring on the arm as necessary. Follow this manual from beginning to end and use the manual that comes with the car lift. The AP-6PL comes with non-slip pads that provide a great contact surface and a set of four high density rubber blocks that help protect lifting points on most vehicles.

High-density roller wheels make the DLR-6P a conveniently portable low-rise lift. The ability to have mobile automotive lifts in your shop allows you to relocate the lift with one person to other areas and use within your shop. They are ideal for tire, wheel and brake related repairs, collision repair work and new car preparation. It is a popular choice for wheel service and body shops. There is also room for some underbody work. This 6,lb.

One of the best Specialty Car Lifts on the market! Includes stop switch at mm from ground and alarm tone when coming down from mm to ground. One of the best 2 Post Car Lifts on the market today! One of the best Low Rise Car Lifts on the market today! With this lift you have more access to undercar repairs when compared to low-rise lifts.

The Dannmar DMR-6 has a compact design that allows it to fit under smaller clearances and comes well-equipped with adjustable arm assemblies. Launch TLTSB Symmetric 2 Post Lift Economical, high quality, clear floor and floor plate chain-over lifts with dual point lock release, steel pulleys, high strength equalization cables and double telescoping screw pads configured to accommodate the smallest Cars to the SUV's and Trucks. Whether you're looking for a car lift for your shop or a home garage lift, there are several of the best options available to you to cover your needs.

Some of the best and most popular car lifts we have are:. The price to install a car lift does depend on which kind of car lift you're installing. A two-post portable car lift for example, probably won't involve modifications to cement flooring. A four-post car lift's price ranges depending on how many pounds it can carry. The optimal height you should have for your garage is about feet of clearance for a new car lift.